Blaupunkt 400US User Manual download pdf (Page 7)

The inputs and controls for this amplifier are explained in the summaries below and reference the numbered call-outs above.

1.) LOW-PASS CROSSOVER CONTROL (ch 1 & 2) - Once the “crossover

frequency setting” is set to “LOW-PASS”, this control adjusts the frequency

for which all signals BELOW this setting are passed on to the speakers.

2.) HI-PASS CROSSOVER CONTROL (ch 1 & 2) - Once the “crossover frequency

setting” is set to “HI-PASS”, this control adjusts the frequency for which all

signals ABOVE this setting are passed on to the speakers.

3.) CROSSOVER FREQUENCY SETTING (ch 1 & 2) - the internal crossover

frequency control setting of the amplifier can be switched to either the “flat”

frequency response position or in a high-pass/low-pass mode. On this

amplifier, the choice is for either 50-250 Hz in LOW-PASS mode or 50-500 Hz

in a HIGH-PASS mode.

4.) HIGH LEVEL INPUTS - Should RCA cables not be available from the radio you

are able to tap onto the audio signal from the high level speaker outputs of the

radio. This is most commonly used when the amp is an add-on device such

as for a subwoofer system.

5.) INPUT GAIN CONTROL (ch 1 & 2) - This controls the gain setting on the input of

the amplifier. For high gain settings ( 0.3 volts), this says that it takes ONLY

0.3 volts to drive the amp to full output. For low gain settings (near 4 volts),

this says that it takes nearly 4 volts to drive the amp to full output. If the amp

is often going into distortion at only moderate volume settings on the radio,

rotate this control towards the 4 volts setting to reduce the distortion.

6.) LOW LEVEL INPUTS - The more commonly used inputs, these are connected to

the standard RCA outputs available on nearly all aftermarket radios today.

These lines are dedicated to left and right outputs of the radio, be it for front or

rear speaker installations. The input gain settings of the amplifier (0.3 - 4

volts) are referenced to these inputs.

7.) INPUT GAIN CONTROL (ch 3) - This controls the gain setting on the input of the

amplifier. For high gain settings ( 0.3 volts), this says that it takes ONLY 0.3

volts to drive the amp to full output.

8.) CROSSOVER FREQUENCY SETTING (ch 3) - the internal crossover frequency

control setting of the amplifier can be switched to either the “flat” frequency

response position or in low-pass mode, 50-250 Hz.

9.) POWER “ON” LED - This light will turn on when the amplifier receives a +12 volt

turn on signal from the radio in the vehicle. The input line to the “trigger”

connection must be properly connected to the radio’s trigger line which is

often also the power antenna line. If the amp is properly wired, but the light does not turn on, verify the trigger line is properly

connected, is receiving +12 volts, and the speaker outputs are not shorted to themselves or ground in any way.

10.) LOW-PASS CROSSOVER CONTROL (ch 3) - Once the “crossover frequency setting” is set to “LOW-PASS”, this control adjusts the

frequency for which all signals BELOW this setting are passed on to the speakers. The power and speaker connections for this

amplifier are explained in the summaries below and reference the numbered call-outs above.

INPUTS & CONTROLS

– 7 –

1 102 3 4 5 6 7 8 9

HIGH-LEVEL – INPUT

GAIN

MIN

MAX

GREEN

GREEN-BLACK

GREY-BLACK

GREY

(NOT USED)

LEFT (+)

LEFT (–)

RIGHT (–)

RIGHT (+)

HIGH-LEVEL – INPUT

GAIN

MIN

MAX

GREEN

GREY

LEFT (+)

RIGHT (+)

RADIO CHASSIS GROUND -OR-

COMMON SPEAKER GROUND

GREEN-BLACK

(NOT USED)

GREY-BLACK

(NOT USED)

"Floating Ground" Radio Outputs

"Common Ground" Radio Outputs

High Level (Speaker Input) Wiring

1 2 3 4 5 6 7 8 9 10 11 12 13

Comments to this Manuals

No comments

Blaupunkt 400US User Manual Page 7

Comments to this Manuals

Related products and manuals for Audio amplifiers Blaupunkt 400US